Benstone Instruments

Born for advanced field testing

Impaq Plus is a fully rugged portable 4 channel real-time analyzer built for advanced noise and vibration measurements in the field.  Manufactured with a rugged enclosure by a dual injection molding process and protective sealing to provide an IP 65 rating for measurement in harsh environments.  Equipped with a large 10.1” multi-touch color display, information is not only on display, but a more intuitive user interface with keypads on the left side. Impaq Plus acquires measurement signal with precision 24 bit sigma delta AD converters to provide a high dynamic range and a up to 40 kHz maximum bandwidth.

With optional software modules, the impaq Plus can conduct FFT spectrum analysis, Order Tracking Analysis and Octave spectrum analysis at the same time. Besides, it can be used as a digital signal recorder for continuous raw data recording and playback analysis. The optional balancing module supports all kinds of field balancing tasks with all the most advanced features.

Multiple Analysis

impaq Plus supports multiple analysis which allows you to run different analysis modules, such
as FFT analysis, Octave spectrum, order tracking analysis and raw data recording, at the same time.

Modular Software

The impaq Plus’s modular software allows for the proper configuration of your analyzer. Optional modules available are raw data recorder, FFT spectrum analysis, 1/3 Octave spectrum analysis, computed order tracking analysis and Rotor balancing.

Raw Data Recorder

The Raw Data Recorder software module allows the user to measure analog signals in the Recorder mode or Real-time Recorder mode and store the raw data signal directly to the hard drive or memory. Replay the stored raw signal in the playback mode with selected analysis modules as if the signal is from a real-time acquisition.

FFT Spectrum Analysis module

The FFT (Fourier Transform) spectrum analysis provides up to 14 different measurement functions for your sound and vibration needs. Continuous start-up/ coast-down spectrum and display the results on a 3D waterfall/ intensity plot. Perform modal, ODS, envelope testing and more.

General sound & vibration analysis
Modal testing and ODS measurement
Sound intensity measurement
Sound and vibration quality measurement
Stiffness measurement
Bearing diagnosis (envelope spectrum and waveform)
Variable speed machine measurement

Octave spectrum analysis module

The octave spectrum analysis utilizes parallel time domain filters to generate octave, 1/3 octave or 1/12 octave spectrum. Conforming to IEC 61260 and IEC 61672 standards, this module is suitable for evaluating the sound or vibration severity. Built-in user defined weighting functions supports specific measurements such as: ISO 6954 (vibration on ships), ISO 8041 and ISO 2631 (human vibration) to name a few. Many high-tech factories are concerned about floor vibration. User defined VC curves can be displayed on the Octave spectrum plot to determine the level of vibration.

Computed Order Tracking module

The computed order tracking program is designed to measure sound and vibration on varying speed machines. A digital re-sampling algorithm is used to make the spectral resolutions be the same at different rotation speeds. Typical applications for this software module are NVH (Noise, Vibration, Harshness) testing of vehicles or advanced vibration analysis of turbine machines. Order spectrum, order traces, filtered or unfiltered orbits, gap reading, and centerline of a shaft are accurately measured and displayed during a start-up or coast-down process.  The user can input geometric position(s) of the vibration sensors to display orbit and shaft centerline motion, which relates to the
realistic behavior of a turbine machine.

Rotor Balancing module

The Impaq Plus’s rotor balancing package can balance your rotating machines in the field with industry leading balancing techniques like; single plane, dual plane, overhung dual plane, 3 plane, 4 plane and 3 weights balancing. This advanced balancing software makes it very simple to balance machines in-field with a very high level of accuracy. Now with multiple-point balancing, vibration in both horizontal and vertical directions are minimized at the same time. By enabling coast-down measurements for 1X vibration, the heavy spot is identified correctly with only one measurement, saving you time, money and
increasing safety. This technique prevents the user from danger by putting the trial weights in the wrong place and shortens the time required to balance. Other features / functions are:

Multi-point balancing
Component calculation
Drill depth calculation
Allowable residual unbalance calculated from the ISO 1940 standard
Unequal radii calculation
Decoupled balancing (couple static)
Review historical vibration data on a polar plot.
Review historical balancing data on a polar plot
Heavy spot estimation with one shot measurement.
Redo a previous balancing job with saved balancing factors.

SPECS :

Operating system
Windows 10 IoT enterprise

Input channels
4 analog channels and 1 tacho channel

Connector
Channel 1 ~ channel 4: BNC. Tri-axial: Fischer Core Series 103*, 6 pins
Tacho input: Fischer Core Series 103*, 7 pins. USB: USB 3.1, Type-A connector

Channel coupling
AC, DC, IEPE

Tacho input
TTL signal, with built-in power supply

CPU
Intel Atom® Processor N4200

Internal memory
256G SSD

Battery
14.4V, 2270mAh, 32.7W* (x2, swappable)

Interface
USB 3.1 type A connector x1

LCD display
1280x800 10.1” multi-touch color screen

Operating temperature
-10 deg C to 50 deg C

Product approvals
CE, RoHs, REACH, China RoHs,
Regulatory Compliance Mark (RCM), UKCA, FCC, KC

Drop test
1.2 meters - MIL-STD 810H

Vibration test
MIL STD 810 transportation

Sealing / Ruggedness
EN60529 IP65

Housing material
Dual material mold injection

Weight
1.9 kg with dual batteries, 1.72 kg with single battery

Size
300 x 195 x 50 mm

Input signal range
± 5Volt, ± 20Volt

A/D converter
24-bit sigma-delta A/D converter

Frequency range
0 Hz~40 kHz (102.4 kHz Max sampling rate)

Feature for Raw Data Recorder

Recorded data
Raw time data and TTL tacho signal

Monitor display
Recorder mode: Waveform, continuous waveform or spectrum
Real-time recorder mode: same as real-time measurement setting.

Storage media
Internal 256G SSD

Data review
Replay data in Playback mode

Maximum bandwidth
40 kHz with 4 channels on, plus tacho channel

Maximum length of recording
limited by memory space

Recording stop
by time, rpm, file size or manual

Feature for FFT Analysis

FFT real time rate
40 kHz with 4 channels on

FFT resolution
100-51,200 lines

Spectral map
3D waterfall or intensity plots for continuous spectrum measurements

Time windows
Hanning, hamming, flattop, rectangular, force, exponential Bartlett, Blackman, Kaiser

Analysis functions
Complex spectrum, power spectrum, cross power spectrum, FRF, time waveform, envelope waveform, envelope spectrum, coherence, PSD, Cepstrum, overall level, mean trend, rate trend, rotation speed.

Engineering units
Automatic units transform with pre-defined conversion table

Zoom FFT
Yes

Average
Off, Linear, exponential, time, peak hold

Trigger
On/Off, triggering source, pre/ post triggering, triggering slope and
triggering level

Map functions
Time waveform, complex spectrum, auto spectrum, cross spectrum

Control of Map measurement
Free run, by total count, total time, armed by time step or RPM step

Cursor
Single, harmonic, dual, side band, peak cursor, cursor marker

Envelope filters
500~2kHz, 1k~2.5kHz, 2k~5kHz, 5k~10kHz or user defined.

2D Plot format
Linear, Polar, Bode, Real Imaginery, Nyquist, Accelerance/Mobility/Compliance

3D Plot format
Waterfall, intensity map, overlapped

Mathematic operation
Unit conversion, FFT, iFFT, integration, differentiation, band pass filter,
high pass filter, low pass filter, band notch filter, scaling, weighting,
window, reciprocal, detrend, redo, undo.

Also you can check product : NEW Benstone Instruments fieldpaq II Portable Sound & Vibration Analyzers

Fieldapaq II Vibration Tester

The fieldpaq II Vibration Tester is a portable, 4-channel, real-time analyzer that is built for advanced noise and vibration measurements in the field. For vibration data acquisition in challenging environments, Fieldpaq II is manufactured with a ruggedized housing, made by a dual injection molding process, and protective sealing to provide an IP65 rating.

- Large 5", color, high resolution (800 x 480) touch screen.  
- Powered by Microsoft's WinCE
- Precision 24-bit sigma delta AD converters
- Up to 40 kHz maximum bandwidth.  
- DSP chip performing real-time analysis
- IP65-rated rugged, high quality housing made by dual injection process

FFT Spectrum Analysis Module

The fieldpaq II Vibration Tester's 2- or 4-channel optional FFT Spectrum Analysis Module allows you to conduct cross-channel analysis such as FRF, coherence, and cross power spectrum, as required for modal analysis, ODS testing or sound intensity measurements. It also supports continuous spectral measurements and waterfall display for vibration testing of varying-speed machines.

- General vibration analysis
- Modal testing
- Sound intensity measurement
- Operational deflection shape measurement
- Bearing diagnosis

With the FFT Spectrum Analysis Module, the fieldpaq II portable vibration analyzer also supports bearing vibration analysis as a standard feature. By taking advantage of demodulation technology, one may see the fault frequencies on a demodulated spectrum to detect early bearing damage.

Octave Spectrum Analysis Module

The optional Octave Spectrum Analysis Module utilizes real-time digital filtering technology to generate octave, 1/3 octave or 1/12 octave spectrum. Conforming to the IEC 61260 & IEC 61672 standards, the Octave Spectrum Analysis Module is suited for acoustic or vibration data acquisition in the field. For vibration applications, the program can perform measurements with user-defined weightings. For example, the fieldpaq II Vibration Tester can perform measurements with the specified weighting of ISO 6954, ISO8041, ISO2631 and more. When measuring floor vibration, the fieldpaq II portable vibration analyzer can display the VC curves on the spectrum, providing real-time evaluation of the vibration severity in the field.

Rotor Balancing Module

The fieldpaq II Vibraiton Tester's Rotor Balancing Module supports simultaneous, 4-channel measurements with a multiple point field balancing technique. Now with multiple-point balancing, vibration is minimized in BOTH horizontal and vertical directions at the same time. By enabling coast-down measurements for 1X vibration, the heavy spot is identified correctly with only one measurement, saving you time and money by eliminating the use of trial weights. It also eliminates safety concerns from placing the trial weights in the wrong location. 

Other field balancing features and functions are:

- Multi-point balancing
- Component calculation
- Drill depth calculation
- Allowable residual unbalance calculated from the ISO 1940 standard
- Unequal radii calculation
- Decoupled balancing (couple static)
- Review historical vibration data on a polar plot
- Review historical balancing data on a polar plot
- Heavy spot estimation with one shot measurement
- Redo a previous balancing job with saved balancing factors
- Continue an unfinished field balancing job from a saved file

Vibration Meter

Overall vibration level is a basic parameter for determining a machine’s operational condition. By simulating the operation of an analog vibration meter, fieldpaq II performs time domain integration, filtering, and root mean square (RMS) calculations, for accurate measurements of vibration levels. One to four channels can be measured at the same time, displaying the results to a trend chart, bar chart, or continuously recorded to a data file. Easily check vibration severity against the built-in ISO 10816-3 standard.

Technical Data:

Fieldpaq II vibration tester and portable vibration analyzer  
- Ruggedized housing, IP65 rating
- 5-inch color (800 x 480 high resolution) touch screen  
- Powered by Microsoft's WinCE
- Acquires measurement signal with 24-bit sigma delta AD converters
- Up to 40 kHz maximum bandwidth
- Powered by a DSP chip for real-time analysis

Data acquisition connectors
- Two BNC connectors for 2-channel measurements.  
- LEMO 4-pin connector to extend to 4 channels 
- AUX channel for tachometer signal input and power supply

External memory card and USB interface
- Store vibration data on the SD card
- USB connection to transferred to a PC

Optional 2- or 4-channel FFT Spectrum Analysis Module
Measures time waveform, orbit, power spectrum, cross power spectrum, complex spectrum, FRF, coherence, PSD and envelope spectrum

- General vibration analysis
- Modal testing
- Sound intensity measurement
- Operational deflection shape (ODS) measurement
- Bearing damage diagnosis

Rotor Balancing Module
The fieldpaq II Vibration Tester's optional field balancing software package supports simultaneous, 4-channel data acquisition with a multiple-point balancing technique. 
By conducting coast-down measurements for 1X vibration, the heavy spot can be easily identified with only one measurement saving you time and money while improving safety.

Vibration Meter Module (optional)
- Measure overall vibration levels in displacement, velocity and acceleration
- Measure Crest factor for detecting bearing damage and failure
- Continuous recording over time or RPM

Octave Spectrum Analysis
- Real-time digital filtering technology to generate octave, 1/3 octave or 1/12 octave spectrum
- Vibration analysis with the special weighting of ISO 6954, ISO8041, ISO2631 and more
- Floor vibration measurements providing real-time evaluation of the vibration severity.

Also you can check product : NEW Benstone Instruments impaq Plus 4 Vibration Analyzer and Sound

VP5 Vibration Data Collector

Advanced Machinery Condition Monitoring and Root Cause Vibration Analysis
VP5 is Benstone’s state-of-the-art, 4-channel portable vibration data collector and analyzer.

- Large 6.4” color, VGA high-resolution touch screen
- Powered by WinCE operating system
- 24-bit sigma delta AD converters
- Up to 40 kHz maximum bandwidth
- High-speed DSP for real-time signal analysis

Portable Vibration Analyzer for Harsh Environments
- IP65-rated housing
- Rugged housing made by a dual injection molding process
- CE mark
- IEC 60068-2-34 vibration test
- IEC 60068-2-27 shock test


VP5 4-channel Vibration Data Collector
Measures triaxial vibration signals, reducing man-hours in the field.

Advanced Field Balancing Module
VP5's field balancing module supports up to 4-plane rotor balancing.
For single- or dual-plane balancing, choose up to 4 measurement points for minimizing vibration levels in different directions and locations.

Locate Heavy Spots with Only 1 Measurement
VP5's advanced field balancing module can record the 1X trace during a coast-down process.
With this information you can locate the heavy spot of your rotor before the trial weight is added, saving rotor balancing time and increasing safety.

Bump Test and ODS Test Modules
Investigate structural resonance with the optional Bump Test Module. 
Complete modal testing is possible when combined with 3rd party software, like ME'Scope.

Raw Data Recorder Module 
The optional data aquisition program directly records raw vibration data to the built-in compact flash card. Post-processing of raw vibration data files, such as FFT, order tracking or octave analysis, can be done from the playback mode with Benstone’s computer-based Novian Dynamic Signal Analyzer Software.

Computed Order Tracking Module
The optional Computed Order Tracking Module is designed to analyze the sound or vibration signals of varying-speed rotating machinery.  Typical applications for this software module are NVH (Noise, Vibration, Harshness) testing of vehicles and advanced vibration analysis of turbomachinery.

VP5 Vibration Data Collector
VP5 is a 4-channel portable vibration data collector and handheld vibration analyzer powered by Microsoft Windows CE and state-of-the-art DSP technology. VP5's rugged housing is made from a high tech, dual-material injection process, consisting of hard ABS plastic (black) and soft TPR plastic (orange). VP5 also has rubber seals for IP65 protection in extreme weather and harsh environments. Equipped with VGA resolution color touch screen, VP5 brings you a state-of-the-art experience with in-field portable vibration analyzers.

- Data Collection and Recording
- Rotor Dynamic Balancing
- Computed Order Tracking
- Data Recorder
- Bump Test
- ODS test

Route-Based Data Acquisition
Combined with the powerful computer-based iSee predictive maintenance software, the field-proven VP5 portable vibration data collector is your best choice for route-based data acquisition.

- Simultaneous tri-axial measurements (x,y,z axes) save hours in the field
- Measures bearing fault signal via true peak detection on a high-pass filtered time waveform
- Sensitive and accurate readings of early-stage of bearing damage allow the user to track bearing damage development via a trending analysis feature in iSee predictive maintenance software
- Envelope spectrum measurement for confirming bearing damage is a standard feature
- Temperature and other process parameter measurements are supported.

Bump Test Module

VP5’s optional and powerful Bump Test Module allows you to measure a structure’s frequency response frequency (FRF), coherence, and cross power spectrum functions. This useful vibration analysis software module helps investigate the resonance of a machine, enact structural reinforcement and reduce the vibration levels of a machine running at its resonance zone. Test data can be imported to a 3rd party software, such as ME’Scope, for further modal analysis to derive its modal shapes, natural frequencies and damping values.

ODS Test module 
VP5’s optional Operational Deflection Shape (ODS) module allows you to conduct a measurement on a running machine and measure its FRF, coherence, and cross power spectrum functions.  With the reference vibration sensor connected to channel 1 and a triaxial vibration sensor connected to channels 2, 3, and 4, the VP5 vibration data collector saves you time in the field with real-time, 4-channel measurements.  By importing the test data to a 3rd party software, like ME’Scope, you can easily derive the operational deflection shapes of your machines at certain running speeds and use this information for structural reinforcement.

Computed Order Tracking Module 
The optional Computed Order Tracking module is designed to analyze the sound or vibration signals of varying-speed machines. Typical applications for this capability are NVH (Noise, Vibration, Harshness) testing of vehicles and advanced vibration analysis of turbine machines.  It accurately calculates the order spectrum, order traces, filtered or unfiltered orbits, gap reading and the centerline of a shaft during a start-up or coast-down process.  The VP5 Vibration Data Collector's order tracking algorithm performs digital re-sampling of the measured signal for ensure data accuracy.  The order spectrum data can be displayed on a waterfall plot or intensity map. Cut a slice or a trace of data from the waterfall plot and then examine the individual traces.  As shown in the figure below, the user can enter the geometric position(s) of the vibration sensor(s) to create a plot to display orbit and shaft centerline motion, which relates to the realistic behavior of a turbine machine.

Raw Data Recorder Module 
The optional Raw Data Recorder Module directly records raw time data to the built-in compact flash card.  For example, a 1 GB file will contain approximately three hours of continuous data with four channels recording at 2 kHz bandwidth.  Benstone's computer-based Novian Dynamic Signal Analyzer Software allows for playback and post-processing of raw data recorder files, such as FFT, order tracking or octave analysis.

Rotor Balancing module
The optional Rotor Balancing Module is a field balancing software package for rotating machines that utilizes industry-leading rotor balancing techniques: single-plane, dual-plane, overhung dual-plane, 3-plane, 4-plane, and 3-weights balancing. This advanced software simplifies field  balancing of machines with a very high level of accuracy.  Now with multiple-point balancing, vibration is minimized in BOTH horizontal and vertical directions at the same time.  By enabling coast-down measurements for 1X vibration, the heavy spot is identified correctly with only one measurement, saving you time and money by eliminating the use of trial weights. It also eliminates safety concerns from placing the trial weights in the wrong location.

SPECS :

Hardware Feature

Operating system
Windows CE

Number of input channels
4 analog channels and 1 aux channel

Connector of input channels
BNC, 4 pin Lemo for triaxial sensor, Aux: 6 pin Lemo

Channel coupling
AC, DC, IEPE

Aux channel
TTL or non-TTL in (external trigger or tacho)

DSP processor
TI TMS320C6713B

External memory
Compact flash card

Battery
Li-Po 7.4V 5800 mAhr, rechargeable

PC communication interface
USB 1.1, mini B type USB connector

LCD display
640X480 6.4-inch TFT color touch screen

Operating temperature
-10 deg C to 45 deg C

Safety certifications
CE

Sealing / Ruggedness
IP 65

Housing material
Dual material: hard ABS plastic and soft TPR

Weight
4.5 lb (2.0 kg)

Size
11.2inch*7.1inch*3.0inch (284mm*180mm*76mm)

Input signal range
±5Volt, ±20 Volt

Dynamic range
>128 dB (measured from spectrum)

A/D converter
24 bit sigma-delta A/D converter

Frequency range
0 Hz~40 kHz

Input impedance
1M Ohm

Feature for Raw Data Recorder

Recorded data
Raw time data and TTL tacho signal

Monitor display
Waveform, continuous waveform or spectrum
(resolution 100, 200 or 400 lines)

Storage media
Compact flash card

Data review
Playback block by block, fast forward or rewind

Maximum file size
1 Gigabyte each

Maximum sampling rate
51.2 kHz for 1 channel, 25.6kHz for 2 channels and 12.8 kHz for 4 channels

Data analysis
Raw data files can be replayed by Novian software with FFT, octave or order tracking analysis.

Feature for Bump Test module

FFT real time rate
40 kHZ, dual channel @12800 lines

FFT resolution
100-12,800 lines

Time windows
Force/Exponential

Analysis functions
power spectrum, cross power spectrum,FRF, time waveform and coherence

Engineering units
Automatic units transform with pre-defined table

Zoom FFT
No

Average
Linear, exponential, peak hold

Trigger
Channel 1 triggering, pre/ post triggering

Cursor
Single, harmonic, harmonic single, peak, band cursor mark cursor

Feature for ODS Test module

FFT real time rate
40 kHZ, dual channel @12800 lines

FFT resolution
100-12,800 lines

Time windows
Hanning window

Analysis functions
power spectrum, cross power spectrum,FRF, time waveform and coherence

Engineering units
Automatic units transform with pre-defined table

Zoom FFT
No

Average
Linear, exponential, peak hold

Trigger
No

Cursor
Single, harmonic, harmonic single, peak, band cursor mark cursor


Feature for Rotor Balancing

Rotor type for balancing
Single plane, dual plane, 3 plane, 4 plane, overhung dual plane, 3 weights balancing

Balancing speed
60 rpm to 300,000 rpm

Order resolution
Low, normal, high, 0.03, 0.015, 0.008, and 0.004

Average number
10, 20, 50 and 100

Balancing grade
Built-in ISO 1940 standard or user defined

Tools
1X coast down order trace, decoupled balancing (static and couple), unequal radii, component
calculation, drill depth, vibration history, balancing history and recalculation of balancing coecients.


Feature for Order Tracking module

Measurement types
Measurement types Order trace, order spectrum, spectrum map, RPM profile, orbit, gap and shaft centerline.

Measurement control
Manual, time step, rpm step or both time and rpm step.

Rotation speed
6 rpm to 480,000 rpm

Order resolution
0.5, 0.25, 0.125 and 0.0624

Max. number of traces
User selectable 16 orders plus overall traces.

Max. order
800 order

Waterfall display
Adjustable waterfall plot and intensity plot

Waterfall cursor
RPM cursor and Order cursor

Y-Axis of order traces
Linear, log, dB, real, image, phase, number and polar plot; Bode plot by layout setting.

Geometry setting
Selectable angular location of sensors


Feature for Data Collector

Types of measurement
Overall acceleration, overall velocity, overall displacement, overall bearing condition (true peak
detection of HP filtered waveform), time waveform, power spectrum (up to six sets), demodulated spectrum, Amplitude&Phase, Cepstrum, Crest factor, temperature, process parameters.

Vibration sensors
support simultaneous 3 axis measurement or single axial

Filters for overall value
2Hz-1kHz, 5Hz-1kHz, 10Hz-1kHz, 2Hz HP, 5Hz HP, 10Hz HP

Overall display
Bar chart or trend chart (shown with latest 9 historical data)

Spectrum display
Show band alarm or fault frequencies.

Time waveform display
Show waveform and/ or orbit

Search
Search train, machine or point

Tools
Add note, skip point, hide archive points, show all points, show archive points only, insert or delete unscheduled points.

Also you can check product : NEW Benstone Instruments fieldpaq II Portable Sound & Vibration Analyzers

The vPod Pro Smart Vibration Meter is designed for machine health monitoring and predictive maintenance.

- IP65-rated case with anti-drop rubber sleeve
- 3.5" color screen
- Built-in 24G flash memory
- Route-based vibration data collector measures bearing condition and temperature at the same time
- Optional spectrum analysis function
- Buit-in camera for taking on-site photos as a note when storing data 
- Supports Bluetooth headset connection for listening to the vibration signal
- USB 2.0 and Wi-Fi transmission interface

Innovatively designed (patent) dual-output sensor A52-IR

- Measure vibration signals in the frequency range of 1~8kHz ( /-1dB) or 0.3~10kHz( /-3dB)  
- High-strength magnetic base to secure the transmission of high-frequency signals
- Infrared temperature sensor inside

Overall vibration measurement
Detect low-frequency vibration of rotating equipment, such as

- Dynamic balance problems with the rotating parts
- Shaft misalignment
- Looseness  
The vPod Pro Smart Vibration Meter's built-in ISO 10816-3 vibration standard displays vibration severity ​​in green, yellow, and red.

Bearing Condition Monitoring

- Measures the bearing signal in the 1 kHz to 10 kHz bandwidth
- Implements the "true peak" value for detecting bearing damage
- Detects and tracks the bearing condition for early damage detection and predictive maintenance
- Detects bearing condition effectively on ultra-low speed machines
- Shows bearing condtions in green, yellow, and red background

Bluetooth headset connection 

- The vPod Pro Smart Vibration Meter has a built-in feature that connects to Bluetooth headsets
- After each measurement, the user can automatically play 2~8 seconds of vibration signal through the Bluetooth headset
- Experienced users can use this auxiliary function to tell whether an equipment is abnormal or not

Camera function

- The vPod Pro Smart Vibration Meter has a built-in camera
- Can be attached to a live shot as a record while storing measurement data
- Photo linked to the measurement data and sent back to the PC-based iSee Predictive Maintenance Software

Spectrum analysis function (optional)

- Spectrum data is measured at the same time as a diagnostic vibration problem
- Select 1 kHz bandwidth of 1600 resolution lines or 10 kHz bandwidth of 6400 resolution lines

- Display the order information of the top 10 peaks

Route-based Vibration Data Collector Module (optional)

- Works with iSee Predictive Maintenance Software
- Measures basic vibration, bearing condition, temperature, and raw vibration signal
- Converts raw signal into a time waveform, two sets of spectrum analysis, envelope spectrum, and cepstrum
- Quickly track problematic measurement points, trend changes, diagnose problems and generate reports.

Innovative design

vPod Pro is our next generation smart vibration meter built around your need in machinery condition monitoring. With the innovatively designed sensor A52-IR, vPod Pro can measure vibration and temperature at the same time. The high-strength magnetic base secures the sensor for accurate transmission of high frequency signals from bearings or gears. After each measurement, vPod Pro displays 3 readings at the same time: vibration level, bearing condition and temperature.  The severity status for each measurement is shown with easy to read background colors.

Superior method for detecting damaged bearings

A damaged bearing will exhibit the periodic knocking signals in its vibration time waveform. vPod Pro implements the field-proven “true-peak” detection, which can track early stage bearing damage.  This detection method also proves to be very effective for detect bearing damage on ultra-low speed machine.

Powerful Utility and Novian sftware for data viewing and post analysis

vPod Pro allows you to listen to the raw signal via a Bluetooth headset, take and attach a picture to the stored data record. With optional Spectrum version, vPod Pro can store the 10 kHz bandwidth raw signal to the built-in memory and let you replay the sound files as many times as you wish.  The users can also conduct post analysis on the  stored raw data with free Utility and Novian software to derive more detailed spectrum data.

Complete features in route mode

In the Route mode; basic vibration, bearing condition and temperature are measured, while in the background the raw vibration signal is stored for further data analysis. When the measured data is imported into iSee computer program, this raw signal is automatically converted into a time waveform, two sets of power spectrum, envelope spectrum, and cepstrum to provide the most complete predictive maintenance monitoring parameters.

Specifications

vPod Pro analyzer/data collector

Processor
ARM® Cortex-A8, 1GHz

Display
3.5” color TFT LCD, 240x320

Storage
24G ash memory

Input Channels
1 analog & 1 digital input

Input Connector
8 pin Lemo connector

Input Range
±5V

Input coupling
IEPE, 2mA/ 19V ±1V

A/D Resolution
24 bits

Max. Sampling Rate
25.6 kHz

Input Impedance
1MΩ

Maximum frequency
10kHz

Analog high pass Filter
-10% at 3Hz, -5% at 5Hz

Max. Input voltage
±20V

Power supply
18650 battery x2

Battery life
6 hours continuous operation

Operating temperature
-10°~60°C

USB
USB 2.0 Client, Type-C connector

Bluetooth
Bluetooth 4.1 For headset

Wifi
802.11 b/g/n 2.4GHz

camera
640x480 pixels

housing
ABS Plastic and rubber sleeve

Certication
IP65, CE Mark, Rohs

Size
204x85x45 mm (8x3.3x1.8 inch)

Weight
0.49 kg (1.05 lb) (with batteries)

Spectrum measurements

Band & resolution
1kHz (1600 lines) or 10kHz (6400 lines)

Window
Hanning window

Cursor
single cursor with auto marking 10 peaks

A52-IR dual output sensor

Vibration sensor
IEPE type accelerometer

Measurement Range
±50 (g)

Sensitivity
100 (mV/g) typical

Frequency Response
1-8 kHz (±1dB), 0.3-10 kHz (±3dB)

Resonance Frequency
34 kHz

Non-Linearity
±1%

Transverse Sensitivity
5%

Shock Limit
5000g

Residual Noise
0.0004 (g RMS)

Temperature sensor
Digital Infrared thermometer

Resolution
0.1°C

Measurement Range
-40°~115°C

Meter Mode

Overall vibration
0-50g (peak)

Units
um,mm,mil;mm/s,in/s; g,mg,m/s2

Filters
3Hz-1kHz, 5Hz-1kHz, 10Hz-1kHz,10Hz-10kHz

Detections
rms, peak, peak-peak (equivalent)

Bearing condition
0~50g (true peak), 1kHz~10kHz

Temperature
-40°~115°C

Route Mode

Number of routes
unlimited

Hierarchic levels
2, machine and point

Archive data
overall vibration,bearing condition, temperature, Spectrum (1kHz/1600 lines), raw data (2 seconds)


Also you can check product : NEW Benstone VP5 Vibration data collector and handheld vibration analyzer

MP5 4-channel Handheld Vibration Analyzer

- Four channel portable vibration data collector and vibration analyzer
- High quality housing by dual injection molding process
- 5" color touch screen
- Route based data aquisition
- Optional bump test module
- Optional ODS test module
- Optional balancing module

Accelerometer Connectors

- Analog input channel: BNC connectors for channel 1 & 2
- Analog input channel: LEMO 4 pin connector for channel 2,3,4
- AUX input channel: LEMO 6 pin, accept tacho signal and provide power supply to Benstone Laser tachometer
- DC: LEMO 3 pin for line power

Vibration Data Collector Module (standard)

Supports simultaneous triaxial measurements, saving working hours in the field.
Measures overall levels, bearing condition, up to 6 sets of power spectrum, Envelope spectrum, time waveform and cepstrum in real-time.

Bump Test module

MP5 Handheld Vibration Analyzer's powerful Bump Test module allows you to conduct bump test on a structure and measure its FRF, coherence, and cross power spectrum functions.  This useful module helps you to investigate the resonance of a machine, conduct structural reinforcement and reduce the vibration level of a machine running at resonance zone. The test data can be imported to a 3rd party software, like ME’Scope, for further modal analysis to derive its modal shapes, natural frequencies and damping values.

ODS Test module

MP5 Handheld Vibration Analyzer's ODS Test module allows you to conduct ODS test on a running machine and measure its FRF, coherence, and cross power spectrum functions.  By importing the test data to a 3rd party software, like ME’Scope, you may derive the Operational Deflection Shapes of your machines easily.  The ODS test helps to find out how the structure deflects at certain running speed, provide useful information for structural reinforcement.

Field Rotor Balancing Module

- Multi-point balancing
- Component and Drill depth calculation
- Allowable residual unbalance calculated from the ISO 1940 standard
- Unequal radii calculation
- Decoupled balancing (couple static)
- Review historical vibration data on a polar plot.
- Review historical balancing data on a polar plot
- Heavy spot estimation with one shot measurement.
- Redo a previous balancing job with saved balancing factors.
- Continue an unfinished balancing job from a saved file

MP5 Handheld Vibration Analyzer

MP5 Handheld Vibration Analyzer is a compact portable 4 channel data collector that is designed for route-based data acquistion.  With optional software modules, MP5 handheld vibration analyzer can conduct field balancing, ODS testing and Bump Testing as well.  For measurements in harsh environments, MP5 is manufactured with a ruggedized housing by a dual injection molding process and protective sealing to provide an IP 65 rating.  MP5 is equipped with a large 5-inch color (800 x 480 high resolution) touch screen.  The combination of Microsoft's powerful WinCE operating system and touch screen operation provides a user friendly and intuitive interface. MP5 acquires measurement signal with precision 24-bit sigma delta AD converters to provide a high dynamic range, up to 40 kHz maximum bandwidth.

Route Based Data Collector and Portable Vibration Analyzer

Combined with iSee, the powerful PC software built for machinery condition monitoring project, MP5 Handheld Vibration Analyzer is your best choice for route-based data acquisition.  MP5 supports simultaneous tri-axial vibration measurement, saving many work hours in the field.  MP5 measures bearing fault signal via true peak detection on a high-pass filtered time waveform.  This field-proven portable vibration analyzer provides sensitive and accurate readings from the early stage of bearing damage, and you can track the damage development from the trending analysis feature of iSee PC software. 
Envelope spectrum measurement is a standard vibration analysis feature for confirming bearing failure.  Temperature and other process parameter measurements are also supported by this handheld vibration analyzer. 

Bump Test Module

MP5 Handheld Vibration Analyzer's powerful Bump Test module allows you to conduct bump test on a structure and measure its FRF, coherence, and cross power spectrum functions.  This useful module helps you to investigate the resonance of a machine, conduct structural reinforcement and reduce the vibration level of a machine running at resonance zone. The test data can be imported to a 3rd party software, like ME’Scope, for further modal analysis to derive its modal shapes, natural frequencies and damping values.

ODS Test module

MP5 Handheld Vibration Analyzer's ODS Test module allows you to conduct ODS test on a running machine and measure its FRF, coherence, and cross power spectrum functions.  With the reference vibration sensor connected to channel 1, and a triaxial vibration sensor connected to channel 2, 3 and 4, MP5 saves your time for the measuring tasks in the field via real-time four channel measurements.  By importing the test data to a 3rd party software, like ME’Scope, you may derive the Operational Deflection Shapes of your machines easily.  The ODS test helps to find out how the structure deflects at certain running speed, provide useful information for structural reinforcement.

Field Rotor Balancing

The MP5 portable vibration analyzer with the (optional) balancing software package can balance your rotating machines in the field with industry leading balancing techniques like; single plane, dual plane, overhung dual plane, 3 plane, 4 plane and 3 weights balancing. This advanced balancing software makes it very simple to balance machines in the field with a very high level of accuracy.  Now with multiple-point balancing, vibration in BOTH horizontal and vertical directions are minimized at the same time.  By enabling coast-down measurements for 1X vibration, the heavy spot is identified correctly with only one measurement, saving you time, money and increasing safety.  This technique prevents the user from danger by putting the trial weights in the wrong place and shortens the time required for rotor balancing.  Other rotor balancing features / functions are:

- Multi-point balancing
- Component calculation
- Drill depth calculation
- Allowable residual unbalance calculated from the ISO 1940 standard
- Unequal radii calculation
- Decoupled balancing (couple static)
- Review historical vibration data on a polar plot.
- Review historical balancing data on a polar plot
- Heavy spot estimation with one shot measurement.
- Redo a previous balancing job with saved balancing factors.
- Continue an unfinished balancing job from a saved file

Also you can check product : NEW Benstone vPod Pro Smart Vibration data collectors and Analyzers